![ford as built data center ford as built data center](https://techcrunch.com/wp-content/uploads/2021/11/GettyImages-885294108-1.jpg)
The VID block will retain the original settings as they were recorded when the vehicle left the factory. If a feature is changed using the customer preference items configuration method, the changed information will not be stored in the PCM VID block.
![ford as built data center ford as built data center](https://i.ytimg.com/vi/ZvkkQZFIzyA/maxresdefault.jpg)
Refer to the Module Configuration Index in this section for a list of features for each module. Not all features controlled by the module are listed in this configuration method. This method is used to enable or disable module-controlled items or systems to suit the preference of the customer. Only contact the As-Built Data Center when directed to do so by the diagnostic tool. The As-Built Data Center will always reflect the original build of the vehicle as it left the factory. The As-Built Data Center records the applicable module configurations stored in each module before the vehicle leaves the factory. The As-Built Data Center keeps a record of the vehicle configuration in a database that is retrievable using the VIN. For more information, refer to the REFER to Powertrain Control/Emissions Diagnosis (PC/ED) manual. The engine calibration information may still need to be flashed.
FORD AS BUILT DATA CENTER INSTALL
If using the PMI routine to install a new PCM, the diagnostic tool will reprogram only VID information. If a new powertrain calibration has been flashed onto the PCM, the VID block will not be affected. The VID block is not related to or affected by the powertrain calibration information stored in the PCM. If the diagnostic tool cannot retrieve option content information from the suspect module, the diagnostic tool will attempt to extract backup information from the VID block of the PCM.
![ford as built data center ford as built data center](https://assets.bwbx.io/images/users/iqjWHBFdfxIU/i3s6rZVVnBQA/v1/-1x-1.jpg)
The VID block is the first backup of information when using the PMI configuration method. A portion of the VID block is used to store the backup data for each programmable module on the vehicle. The PCM contains a memory area called a vehicle identification (VID) block. It has no effect on the backup data in the VID block memory area of the PCM. NOTE:Flash programming powertrain calibrations onto the PCM is different than PMI. Make sure the new module is on hand for installation before retrieving option content information data from the old module.Īfter the new module is installed, use the diagnostic tool to restore the option content information into the new module. Once information is stored, the diagnostic tool cannot be used to retrieve any other option content information without erasing the previous option content information. The diagnostic tool can store the combined option content information and VIN for only one module at a time. The diagnostic tool will then store the option content information and the VIN. If DTC B2477 is not present the module will allow the diagnostic tool to retrieve its option content information.
![ford as built data center ford as built data center](https://i.ytimg.com/vi/9C_84iBmK3Y/hqdefault.jpg)
FORD AS BUILT DATA CENTER HOW TO
The PMI routine will then halt and give instructions on how to proceed. If DTC B2477 is present the module does not contain complete configuration information.Once the VIN is retrieved the diagnostic tool will carry out a self-test of the suspect module to determine if the module has been configured. the vehicle identification number (VIN) from the PCMĭuring PMI the diagnostic tool first looks to the PCM for the VIN of the vehicle.option content information from the old module (module configuration and customer preference settings).During the PMI routine the diagnostic tool attempts to gather two pieces of information: The PMI configuration method is used when a new programmable module is to be installed. Make sure to use the flash cable when programming calibrations or running a PMI routine on the PCM. NOTE:If the powertrain control module (PCM) needs to have a powertrain calibration flash programmed, refer to the REFER to Powertrain Control/Emissions Diagnosis (PC/ED) manual. This is the only time the As-Built Data Center should be contacted. If this also fails, the diagnostic tool will display instructions to contact the As-Built Data Center. If this is unsuccessful, the diagnostic tool will use the first backup and attempt to extract the module configuration information from the VID block in the PCM. Second backup is the As-Built Data Center.ĭuring PMI, the diagnostic tool will attempt to extract the module configuration information from the module to be changed.First backup location is the VID block memory of the powertrain control module (PCM).Primary location is the memory of the specific module.One primary storage location and two secondary (or backup) storage locations. There are three storage locations for module configuration information. There are two different methods of module configuration: The process used to change the settings and customer preference items is module configuration. Some modules support the ability to change specified factory configuration settings and preset preference items.